克魯勃4UH1-100N食品級齒輪潤滑油

深圳市新盛龍潤滑油有限公司為您提供克魯勃4uh1-100n食品級齒輪潤滑油。klüberoil 4 uh1-32...1500 n是用于食品加工潤滑劑和制藥業。他們滿足的要求德國法律管轄食品和相關輔助設備lmbg，秒5，-句，1和美國提出的要求--會21 cfr“準則fda的規定“和178.3570是符合要求nsf h1注冊。klüberoil4 uh1-68...1500 n油符合中電的要求。當測試在fzg齒輪試驗臺根據根據din51354，第2部分，a /8,3/90，油呈劃傷負載> 12和具體損失重量<0.2毫克/千瓦時。-是制定了在使用食品加工和制藥產業，這些潤滑油展-的抗磨損和極壓性能以及-lowtemperature特征。腐蝕防護性能這些油都是-的作為是他們的老化和氧化穩定性。他們因此，有一個高抗剪切并沒有泡沫。
應用：klüberoil4 uh1用于潤滑的摩擦點在食品加工和制藥機械。它們尤其適合為鞭策，斜面和潤滑蝸桿齒輪，軸承，主軸和關節，以及電梯，驅動器和在低溫下輸送鏈。
包裝規格：20升罐200升鼓
英文：
klüberoil 4 uh 1-32 n … 1500 n oils
synthetic lubricating oils for the food-processingand pharmaceutical industries
desc ription
klüberoil 4 uh 1-32 n…1500 n oils
are lubricants for the food processing
and pharmaceutical industry.
they meet the requirements of the
german law governing food products
and asso-ted ancillaries
(lmbg, sec. 5, para 1, sentence 1)
and the us requirements set forth in
the "guidelines of sec. 21 cfr
178.3570 of fda regulations" and
are in line with the requirements of
nsf h1 registration.
klüberoil 4 uh 1-68…1500 n oils
meet the clp requirements. when
tested on the fzg gear test rig according
to din 51 354, part 2,
a/8,3/90, the oils showed a scuffing
load of > 12&a specific loss of
weight of < 0.2 mg/kwh.
food-processing&pharmaceutical
industries, these lubricating oils exhibit
good antiwear&ep properties
as well as excellent lowtemperature
characteristics.
the corrosion protection properties
of these oils are very good as is their
ageing&oxidation stability. they
also have a high resistance to shear
and do not foam.
application
klüberoil 4 uh 1 oils are used for the
lubrication of friction points in foodprocessing
and pharmaceutical machinery.
they are espe-lly suitable
for the lubrication of spur, bevel and
worm gears, bearings, spindles and
joints, as well as of lift, drive and
conveyor chains at low temperatures.
application notes
when used in gears, klüberoil 4 uh
1 oils may be applied by immersion,
immersion circulation/injection.
drip-feed lubrication (e.g. for chains)
and application by brush/oil can is
also possible.klüberoil 4 uh 1 oils are miscible
with mineral oils&polyalfaolefin
oils. however, we recommend
cleaning the oil circulation system or
flushing it with the new oil prior to
using klüberoil 4 uh 1 for the first
time. espe-lly with a view to the
h1 requirements in the foodprocessing
industry, any mixing of
klüberoil 4 uh 1 oils with non-foodgrade
lubricants should be avoided.
for permanent temperatures at the
seal edge up to 100 °c, nbr seals
(acrylonitrile-butadiene rubber) may
be used. for higher temperatures, it
is safer to use fkm seals (fluorinated
rubber) instead. it should be
noted that elastomers from one or
several manufacturers can behave
differently. therefore the data given
in the "compatibility with elastomers"
table should be used for reference
purposes only. a compatibility test
should always be carried out with
the elastomers which are actually
used.
viscosity selection for rolling bearings
and gears
to select the correct oil viscosity,
observe the bearing manufacturers
instructions/refer to worksheet 3
from the society of tribology (gft).
for determining the correct viscosity
for gears, the manufacturers instructions
take priority.
only in cases where there are no
gear manufacturers instructions, the
viscosity can be selected in accordance
with the enclosed worksheet
"klüberoil 4 uh 1 oils – selection of
oil viscosity for gears".
service temperature range*:
iso vg 32 to 100
approx. - 35 °c to approx. 120 °c
iso vg 150 to 460
approx. - 30 °c to approx. 120 °c
iso vg 680 to 1500
approx. - 25 °c to approx. 120 °c
when used for loss lubrication, the
lubricant may be exposed to higher
temperatures, depending on the
relubrication intervals. we will be
pleased to provide samples for testing.
* service temperature range:
service temperatures are guide values which depend
on the lubricants co-ition, the intended
use&the application method. lubricants change
their consistency, viscosity/apparent dynamic
viscosity depending on the mechano-dynamical
loads, time, pressure&temperature. these
changes in product characteristics may affect the
function of a component.
     聯系時請說明是在云商網上看到的此信息，謝謝！
     聯系電話：0755-23448152，13530318069，歡迎您的來電咨詢！
     本頁網址：http://www.hkjzdrp.cn/cp/19318093.html
     推薦關鍵詞： 抗磨液壓油, 機床導軌油, 合成齒輪油, 冷凍機油, 工業潤滑脂