物料由進料裝置經入料中空軸螺旋均勻地進入磨機一倉，該倉內有階梯襯板或波紋襯板，內裝各種規格鋼球，筒體轉動產生離心力將鋼球帶到一定高度后落下，對物料產生重擊和研磨作用。物料在一倉達到粗磨后，經單層隔倉板進入二倉，該倉內鑲有平襯板，內有鋼球，將物料進一步研磨。粉狀物通過卸料箅板排出，完成粉磨作業。
the fritsch vibratory micro mill pulverisette 0 grinds your sample through impact&friction by which the mortar vibrates electro---ically&the grinding material transfers the vibrations to the grinding ball. at the beginning of the grinding，洛陽球磨機哪個牌子好， the comminution of the coarse particles is achieved by the impact effect of the grinding ball. next， the fine particles are comminuted through friction by the tumbling motion of the grinding ball as the vibrations subside. the impact energy of the grinding ball is freely adjustable thus， allowing it to be precisely adapted to the sample being ground.
維護檢修對球磨機的維護和檢修是一項經常性的工作，維修工作的好壞直接影響球磨機的運轉率和使用壽命，洛陽球磨機進口品牌，那么在使用過程中如何正確的維護和檢修，洛陽球磨機廠家報價，下面給予介紹:
1、所有潤滑油在磨機投入連續運轉一個月時應全部放出，-清洗，更換新油。以后結合中修約每6個月換油一次。
2、各潤滑點潤滑情況和油面高度至少每4小時檢查一次。
3、磨機運轉時，主軸承潤滑油的溫升不超過55℃。
for fine comminution of dry laboratory samples/solids in suspension. for homogenisation of emulsions/pastes.
the vibratory micro mill pulverisette 0 is recommended for sample preparation of rohs tests (restriction of hazardous substances).
(三)上述負荷量的增加和試運轉時間的長短，以大小齒輪和減速機齒輪的跑合情況(溫升、噪音、齒面接觸等)為依據進行確定。在齒面接觸精度沒有達到設計要求前，球磨機，不得滿負荷運轉。
(四)試運轉中冷卻、潤滑系統應工作正常，主軸承、傳動軸承、減速機溫度應正常。
(五)裝入2/3數量的鋼球試運轉24-48小時后，應檢查并再次擰緊全部螺栓。
(六)試運轉工作要認真做好各項記錄。
球磨機主要用于陶瓷原料的混合、研磨，是生產各類陶瓷產品的必需設備，該機采用自耦減壓啟動，降低起動電流，其結構分為整體式和獨立式。采用三角帶傳動，單級或雙級減速，配有裝卸獨立小功率電機。
for fine comminution of dry laboratory samples/solids in suspension. for homogenisation of emulsions/pastes.
the vibratory micro mill pulverisette 0 is recommended for sample preparation of rohs tests (restriction of hazardous substances).
登錄后臺
