麥汁壓濾機泵-壓濾機泵-程躍泵業(查看)

壓濾機-泵適用崗位

1.壓濾機-泵可輸送100℃溫度以內的各類腐蝕性和非腐蝕性清液和料漿及各類濾機加壓喂料用泵。例如：有色金屬的鋅、銅、鈷、鎳

、錳等濕法；淀粉、造紙工藝中的污水、污泥的壓濾機入料，臺煉工藝的壓濾機配用泵、礦山選礦、非金屬礦產加工高嶺土等工藝中的漿體輸送泵，產業中污泥、廢渣輸送泵，壓濾機-泵進料泵，其它化工、染料、紙藥、食品生產工藝中的壓濾泵。

2.長期逼壓運行泵出口壓力高輸送腐蝕性介質的崗位，如煙氣脫硫、---治理中的壓力噴淋泵、壓力沖洗泵等。

3.其它需要高壓力無堵塞、無泄漏等污水輸送的場合。

壓濾機-泵使用注意

壓濾機-泵禁止盲目開大出口閥門，以免造成燒壞電機。需啊喲調整排料量時，切記應調整出口閥門，壓濾機-泵的結構，調整進料閥門易造成泵汽蝕，損害---。如果泵的進料頁面過過20m或進料壓力過大而造成盤根漏料時要適當押金盤根，達到不漏料為宜，不可壓的過緊。

壓濾機-泵停止工作操作

為了避免停泵漏料，停泵前可適當壓緊一點盤根。關閉進口閥門，并馬上停泵，以免發生倒壓造成泵的反轉發生設備損壞和盤根向外漏料。并快速打開放料閥門，---慢慢打開泵的出口閥門，將出料管內的物料放完，為了避免雜質在泵腔內沉積堵塞，---時要安裝沖洗水管進行沖洗。壓濾機-泵

pay attention to the use of feed pump of filter press

it is forbidden to blindly open large outlet valves in order to avoid burning out the motor. when you need to adjust the discharge volume， remember to adjust the outlet valve. adjusting the feed valve can easily cause pump cavitation， causing great damage. if the feed page of the pump is too high (more than 20m)/the feed pressure is too high to cause the leakage of the packing roots， the appropriate depsit for the packing roots should be made， so as not to leak， not to press too tight.

stop operation of feed pump of filter press

in order to avoid leakage during shutdown， a little packing can be properly pressed before shutdown. close the inlet valve&stop the pump immediately so as not to cause the back pressure of the pump to cause damage to the reverse generating equipment&leakage of the packing roots.&quickly open the discharging valve，壓濾機-泵，&finally slowly open the outlet valve of the pump，麥汁壓濾機-泵， discharging the material in the feeding pipe， in order to avoid impurity depsition in the pump chamber clogging， if necessary， to install a flushing pipe for flushing.